Top 10 typical forklift crashes ， forklift procedure must take notice of these issues ！.

Top 10 typical forklift crashes ， forklift procedure must take notice of these issues ！.

Blog Article

Do not underestimate the forklift at the workplace. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift freight obstructed the motorist's view, and the individual ahead might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the staff members utilized their body weight as the counterweight, which nearly triggered casualties.
Case 3: The width of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not wear the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was squashed.
Forklift operation should pay attention to these issues ：.

Begin.
1. Prior to beginning, observe the surroundings, and after validating that there are no challenges that hinder the security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be secure before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the task website or while driving, be careful that there will be no barriers overhead. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be reduced to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed side security and topple. .
5. When the forklift is downhill, it is strictly forbidden to shut off the fire and slide, and it is prohibited to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to follow the website traffic rules in the manufacturing facility and have to maintain a certain safety distance from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load shall not be elevated other than when piling or filling. .
8. The elevation of the tons should not block the driver's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive across the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is prohibited for workers to stand on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a prompt way, and they will never ever run with diseases or conceal them.

filling and discharging.
1. When fork-loading items, the range between the two forks need to be changed as needed to make the lots of the two forks well balanced and not skewed, and one side of the item need to be against the shelf. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In unique conditions, security indication must be set up to advise surrounding pedestrians. .
3. In the process of loading and unloading things, the forklift should be stopped with the brake. .
4. The speed of the car should be sluggish and consistent. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled things and injure people. .
5. When making use of a fork to fork the goods, the fork should be as deep as possible under the lots, and it needs to be kept in mind that the fork pointer need to not touch other goods or objects. The load should be stabilized with marginal back tilt of the gantry to ensure that the tons does not glide backwards. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at high speed and collide with difficult things with the fork head. .
7. When the forklift is working, it is forbidden for people to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to use forks to lift workers to take part in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's view and does not surpass 1 min).
4. Eliminate the secret. Stand-on Electric Pallet Stacker .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water must be added.
2. Check the safety efficiency of beginning, running and stopping.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leakage needs to likewise be inspected and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the car;.
2. When you run into somebody in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the incline is enabled.
7. Do not drive across the slope. Stand-on Electric Pallet Stacker When the slope is above 10%, the vehicle must be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and most likely to the driver's line of vision, they should take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia force to grab the goods.
6. It is not allowed to utilize stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the list below conditions.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844